The Mill Gasket is used in the Kitchen Mill™ to create a seal between the mill motor and the mill pan. Order a replacement if your Mill Gasket becomes lost or damaged.

Mill Gasket is rated 4.5 out of 5 by 2.
Rated 5 out of 5 by from Wheat Grinder Mill Gasket The Mill gasket come in two adhesive strips. Clean the surface well before adhering. Be cautious as you apply it as it sticks very well and may not come off if you miss place it. Fortunately for me, the strips were a little bit longer than I needed. Works great.
Date published: 2014-11-01
Rated 4 out of 5 by from Easy to install This gasket was very easy to install! It's a great replacement for the original installed at the factory.
Date published: 2014-06-21
  • 2015-09-01T06:41CST
  • bvseo_cps, prod_bvrr, vn_cps_3.1.6
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_2
  • loc_en_US, sid_SRV-679, PRD, sort_relevancy
  • clientName_blendtec

Is this Mill Gasket for the blendtec jar ?  My  rubber gasket under the blendtec jar is broken. Does it the right stuff for my blendtec jar? Thanks for reply.

Asked by: Evangeline
This is not for the jar, it is for the Kitchen Mill. It sounds like you need your jar replaced. If it's still under warranty, it'll be free to replace. Please give our customer service team a call at 1-800-748-5400 and they'll help you out!
Answered by: BlendtecJess
Date published: 2015-08-25

Why can't I get a new rubber gasket that I can take off and clean. I can not clean one that is attached to the motor housing and replacing it every time I use the kitchen mill is not feasible or cost effective

Asked by: Shahska
The gasket for the mill is designed to only need to be removed if it becomes damaged. There should not be a need to clean where it sticks on, cleaning around should be sufficient. If you have further concerns about this, Customer Service at 1-800-253-6383 can discuss with you proper care for the mill and mill accessories.
Answered by: AdamBlendtec
Date published: 2015-01-27

how do you replace the mill gasket? how do I take the old one out and place the new one on?

Asked by: franz
The old gasket should just peel right off from under the housing. All of our new gaskets have an adhesive backing to stick back in the same place under the housing. The new gasket will need to be cut to fit into place. If you would like additional assistance, you can call Customer Service at 1-800-253-6383 and they should be able to help.
Answered by: AdamBlendtec
Date published: 2015-01-12

I need to replace the rubber gasket that goes between the motor and the clear plastic bin. It is a circular gasket unlike the one shown. I have Model 91. Please advise price and availability.

Asked by: Raymond
Please call 800.748.5400 for assistance.
Answered by: Blendtec
Date published: 2015-02-01

Will this gasket work on an old (about 30 year old) Magic Mill III. Does it attach with adhesive or what?

Asked by: Lilaz
Our gasket is not compatible with the Magic Mill III.
Answered by: Blendtec
Date published: 2014-08-18
  • 2015-09-01T07:06CST
  • bvseo_cps, prod_bvqa, vn_cps_3.1.6
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_5
  • loc_en_US, sid_SRV-679, PRD, sort_recentAnswersFirst
  • clientName_blendtec